Quantity per Order: 1

Includes one Puck Extraction Tool (QD-P112) and one set of Puck Adjustment Tools (QDS-4084-106 and QDS-4084-107)

Quantity per Order: 1

Puck adjustment tool, Inner ring

Quantity per Order: 1

Puck adjustment tool, Outer ring

Quantity per Order: 1

The tool to insert and remove sample pucks in and out of the sample chamber. Compatible with PPMS and Dynacool

Quantity per Order: 1

The tool to insert and remove sample pucks in and out of the sample chamber. Compatible with Versalab

Quantity per Order: 1

Blank puck without wiring. Usually used for sample chamber pin protection or for customer made experiments.

Quantity per Order: 1

Places Heat Capacity or Electrical Transport pucks in vertical orientation. Does not include measurement stages (compatible with P104, P107B or P107E). See Application Note QDS-1085-156 for details.

Quantity per Order: 1

The station allows testing pucks and performing test measurements outside of the sample chamber.

Quantity per Order: 1

Breakout box for all PPMS family platforms. Includes two sets (12+1) of banana connectors and two lemo (male, female) connectors for direct access to the sample chamber wiring.

Quantity per Order: 1

Breakout box for all PPMS family platforms. Includes two sets (12+1) of coaxial connectors and two lemo (male, female) connectors for direct access to the sample chamber wiring.

Quantity per Order: 1

An essential maintenance part for the VSM/ACMSII coilsets and guide tubes. Self-adhesive

Quantity per Order: 1 set

Three bindles with hardware and options manuals

Quantity per Order: 1 kit

Includes LHe Transfer Line (QDS-4047-009), Ultra Torr Fitting, 2 x Long Extensions, 1x Long Extension with Filter, 1 x Short Extension. Compatible with PPMS and MPMS, not for MPMS3

Quantity per Order: 1

LHe Transfer Line Only (Outer Diameter = 9.6mm), no extensions or adapters. Compatible with MPMS or PPMS, not for MPMS3.

Quantity per Order: 1

Sensor for verifying the magnetic field calibration. Used with P102 sample puck and DC Resistivity option. See Service Note QDS-1084-309 for details.

Quantity per Order: 1

"Small Cryopump" is attached to Baffle assembly and used with TTO and Heat Capacity options at low temperatures.

Quantity per Order: 1

Classical sample holder, usually called as "puck". Simple and effective way to secure and wire samples for electrical measurements. Provides 3 channels with four contacts each. The gold-plated contact pads allows either soldering or wire-bonding.

Quantity per Order: Set of 3

The board provides three channels for electrical measurements. Channel 1 is reserved for thermometer of the Horizontal Rotator. Each channel has 4 golden pads for contacts.

Quantity per Order: Set of 3

The board provides three channels for 4-point electrical measurement and shows layout 5-point hall measurement. Channel 3 is reserved for thermometer of the Horizontal Rotator. Each channel has 4 golden pads for contacts.

Quantity per Order: Set of 3

The board has 12 golden pads for electrical contacts, wired to match pins layout of the sample chamber. Usually used for customer made experiments.

Quantity per Order: Set of 2

The board allows placing samples in vertical orientation (parallel to applied field). The board has 12 golden pads for electrical contacts, wired to match pin layout of the sample chamber. Channel 1 is reserved for the horizontal rotator thermometer.

Quantity per Order: 1

An assembly allowing testing all Rotator Sample Boards in QD-P150 Wiring Station. Not for use at low temperatures.

Quantity per Order: 1

Provides two 4-contact channels for electrical measurements in He3 temperature range.

Quantity per Order: 1

Heat Capacity puck designed for use with He3 Option. Uncalibrated.

Quantity per Order: 1

Provides two 4-contact channels for electrical measurements in DR temperature range. Made of gold coated silver, one edge is sanded to show this.

Quantity per Order: 1

Dynacool DR Heat Capacity. Not compatible with PPMS, uncalibrated.

Quantity per Order: 1

PPMS DR Heat Capacity Puck. Not compatible Dynacool, uncalibrated

Quantity per Order: 1

The puck provides two channels with 5 contacts each, designed and wired for use with ACT Option. The gold-plated contact pads allows either soldering or wire-bonding.

Quantity per Order: 1

Standard puck for Heat Capacity option. Uncalibrated.

Quantity per Order: 1

Can be used as spare/replacement for QD-P107A or as individual sample stage with Vertical Puck (QD-P111). Uncalibrated.

Quantity per Order: Set of 2

Board designed for use with TQ Chip

Quantity per Order: 1

The chip has two legs, max applied torque is ~1e-5 N-m. Uncalibrated

Quantity per Order: 1

The chip has three legs, max applied torque ~1e-4 N-m. Uncalibrated

Quantity per Order: 1

The chip has two legs, max applied torque is ~1e-5 N-m. Calibrated at QD.

Quantity per Order: 1

The chip has three legs, max applied torque ~1e-4 N-m. Calibrated at QD.

Quantity per Order: 1

TTO puck only, without Thermometers and Heater shoe assemblies.

Quantity per Order: 1

The set Includes two Thermometers and one Heater shoes for use with TTO puck. Uncalibrated.

Quantity per Order: 1

Spare Thermometer Shoe Assembly for use with TTO puck. Uncalibrated.

Quantity per Order: 1

Spare Heaer Shoe Assembly for use with TTO puck. Uncalibrted

Quantity per Order: Set of 30

The Disks with two leads are made of gold-plated OFHC copper and allow an easy way for attaching thermal leads in 2-point configuration. Disc diameter is 6.3mm, the leads lengh is 0.5mm and width 0.6mm, thickness 0.25mm.

Quantity per Order: Set of 10

The Leads are made of gold-plated OFHC copper and used for attaching thermal leads in traditional 4-point as well as 2-point configuration. Length is 152mm, width is 0.6mm, thickness is 0.25mm.

Quantity per Order: 1

TTO thermometer shoe with voltage lead free instead of soldered to the shoe body. Designed for accomodating Nernst-Ettingshausen measurements with TTO Option.

Quantity per Order: Set of 2

The copper sample is cut in the shape allowing convenient way for attaching TTO shoes for their calibration.

Quantity per Order: Set of 2

The commercially pure nickel 201 sample is cut in the shape allowing convenient way for attaching TTO shoes for test measurements and caliblration verification.

Quantity per Order: 1

Standard VSM coilset. Requires standard Sample Rod and Guide tube (P526A & P526D for PPMS/Dynacool or V536A & V536B for Versalab).

Quantity per Order: 1

Robust samle holder, has 3.5mm inner diameter, 4mm outer diameter and ca. 91 mm length. Can be combined with P125E VSM Powder Sample Holders or with QDS-4096-399 Quartz Braces. Not compatible with MPMS3.

Quantity per Order: 1

Magnetically clean quartz holder, ideal for samples with small moments. The holder geometry allows placing the samples close to the geometrical center of pickup coil. Flat surfact is 4 mm wide, length is ca 91mm.

Quantity per Order: Set of 50 pairs

Sample holder for powder samples. A pair of parts is assembled together to press the powder sample in a piston-cylinder fashion. Made of polypropylene. For use with brass sample holder QD-P125A.

Quantity per Order: 1

The quartz braces/cylinders allow mounting a sample perpendicular to the magnetic fiels. For use with brass sample holder QD-P125A or C130B Brass Sample Holders.

Quantity per Order: 1

The shims allow mounting a sample perpendicular to the magnetic field. For use with P125B or C130A Quartz Sample Holders.

Quantity per Order: 1

Standard Sample Rod made of carbon fiber. Diameter of blue bearing = 7.6 mm. Compatible with PPMS/Dynacool Standard VSM and ACSMII options.

Quantity per Order: 1

Guide tube with inner diameter 7.6 mm. Compatible with PPMS/Dynacool Standard VSM and ACMSII options.

Quantity per Order: 1

Standard Sample Rod made of carbon fiber. Diameter of blue bearing = 7.6 mm. Compatible with Versalab Standard VSM and ACMSII options.

Quantity per Order: 1

Guide tube with inner diameter 7.6 mm. Compatible with Versalab Standard VSM and ACMSII options.

Quantity per Order: 1

Station for mounting samples at at 35mm mark, for use with Standard and Large Bore VSM Option.

Quantity per Order: 1

Pd reference sample, not mounted. The sample has 99.99% purity, L=3.81mm, D=2.7mm, defined mass ans magnetic susseptibilty (see Certificate QDS-1041-001 for details).

Quantity per Order: 1

For The Pd reference sample (QD-C210A) mounted in brass sample holder and used for VSM calibration and verification.

Quantity per Order: 1

Removable upper part with intergrated 6 magnets for perfect positioning and good attachement of the Sample Rod to VSM Transport. Compatible with all PPMS Family VSM/ACMSII and MPMS3 sample rods.

Quantity per Order: 1

The flexture is designed to be a multi-function aligner and resonance attenuator. Compatible with PPMS Family VSM/ACMSII as well as with MPMS3 Sample Rods.

Quantity per Order: 1

Lower Slide and Centering Adapter for Standard VSM/ACMSII Sample Rod, d=7.6mm.

Quantity per Order: 1

VSM coilset with enlarged bore. Requires Large Bore Sample Rod and Guide tube (P526B & P526E for PPMS/Dynacool or V536C & V536D for Versalab).

Quantity per Order: 1

Robust sample holder with 5.5mm inner diameter. For use with Large Bore VSM coilset only.

Quantity per Order: 1

Sample Holder optimized for thin film or flat samples, sample can be secured without glue using small teflon screw.

Quantity per Order: 1

Large Bore Sample Rod, diameter of blue bearings = 10.3mm. For use with PPMS/Dynacool LB VSM Option.

Quantity per Order: 1

Guide tube with inner diameter 10.3mm. Compatible with PPMS/Dynacool LB VSM Option.

Quantity per Order: 1

Large Bore Sample Rod, diameter of blue bearings = 10.3mm. For use with Versalab LB VSM option.

Quantity per Order: 1

Guide tube with inner diameter 10.3mm. Compatible with Versalab LB VSM Option.

Quantity per Order: 1

Lower Slide and Centering Adapter for Large Bore VSM Sample Rod, d=10.3mm.

Quantity per Order: 1

This heater stick is a high-end sample holder with lithographed heater and thermometer, which allows for magnetic measurements up to 1000 K. Surface is 5mm wide. Sample are usually mounted using QDS-4097-030 Zircar Cement and QDS-4505-141 Copper Foil.

Quantity per Order: Set of 10

Annealed copper foil, 12mm x 30mm. The foil is used to wrap around sample installed on the QD-P127A Heater Stick, providing a good isothermal region and minimizing magnetic dipole sources due to the foil's homogeneity.

Quantity per Order: 1

For use with samples that are affected by the moisture in water-based Zircar cement. Includes 3x dry mount plates, 10x staples and 10x copper foil coupons.

Quantity per Order: 1

Station for mounting samples at at 35mm mark, specifically designed for use with VSM Oven Option.

Quantity per Order: 1

Sample rod made of carbon fiber with feed-through wires, used with QDS-P127A VSM Oven Heater Stick. Compatible with PPMS/Dynacool.

Quantity per Order: 1

Sample rod made of carbon fiber with feed-through wires, used with P127A VSM Oven Heater Stick. Compatible with Versalab.

Quantity per Order: 1

Adapter allowing using straws with ACMSII and MPMS3 Sample Rods.

Quantity per Order: 1

Station for mounting samples at 25mm mark. For use with ACMSII Option.

Quantity per Order: 1

GGG reference sample (P507) mounted in quartz tube sample holder. For use with ACMSII Option

Quantity per Order: 1

AC standard reference sample (GGG), not mounted. Has same shape and size as Pd sample.

Quantity per Order: 1

Quantity per Order: 1

Quantity per Order: 1

Sealed bucket for liquid or air sensitive samples

Quantity per Order: 1

Cup only

Quantity per Order: 1

Quantity per Order: 1

Magnetically clean quartz holder, ideal for samples with small moments. The holder geometry allows placing the samples close to the geometrical center of pickup coil. Flat surfact is 4 mm wide, length is ca 152mm.

Quantity per Order: 1

Commonly used as a robust holder for larger moment samples (usually > 1E-5 emu). It has 3.5 mm internal diameter and ca. 152 mm length.

Quantity per Order: 1

Sample rod made of carbon fiber. Usually used with C130A or C130B sample holders.

Quantity per Order: 1

Removable upper part with intergrated 6 magnets for perfect positioning and good attachement of the Sample Rod to VSM Transport. Compatible with all PPMS Family VSM/ACMSII and MPMS3 sample rods.

Quantity per Order: 1

Lower Centering Adapter for MPMS3 Sample Rod.

Quantity per Order: 1

The flexture is designed to be a multi-function aligner and resonance attenuator. Compatible with MPMS3 Sample Rod.

Quantity per Order: 1

Station for mounting samples at at 66 mm mark, for use with MPMS3.

Quantity per Order: 1

Pd reference sample, not mounted. The sample has 99.99% purity, L=3.81mm, D=2.7mm, defined mass ans magnetic susseptibilty (see Certificate 1041-001 for details).

Quantity per Order: 1

The Pd reference sample (C210A) mounted in quartz tube sample holder and used for MPMS3 calibration and verification. Compatible with MPMS3.

Quantity per Order: 1

LHe Transfer Line. Compatible with MPMS3 only.

Quantity per Order: 1

Wired Access Port for MPMS3. New style, with locking latch to avoid opening due to overpressure in sample space. Can hosts up to 4 connector plugs for various options. Shipped with 4x connector plugs.

Quantity per Order: 1

Sample rod made of carbon fiber with feed-through wires, usedwith QD-C145 MPMS3 Heater Stick.

Quantity per Order: 1

This heater stick is a high-end sample holder with lithographed heater and thermometer, which allows for magnetic measurements up to 1000 K. The 4505-141 Copper Foils and 4097-030 Zircar Cement are used as a companion for sample mounting. Surface is 5mm wide.

Quantity per Order: set of 10

17mm x 30 mm, annealed coper foils. The copper foils are used to wrap the sample around the C145 Heater Stick, providing a good isothermal region and minimizing magnetic dipole sources due to the foil’s homogeneity.

Quantity per Order: 1

Station for mounting samples at at 66mm mark, specifically designed for use with MPMS3 Oven Option.

Quantity per Order: 1

Sample rod made of carbon fiber with feed-through wires for MPMS3 ETO Option. Used with M607 or M608 sample holders.

Quantity per Order: 1

In-Plane Stage for ETO measurement in MPMS3.

Quantity per Order: 1

Out-of-Plane Stage for ETO measurement in MPMS3

Quantity per Order: 1

AC standard reference sample (GGG), not mounted. Has same shape and size as Pd sample.

Quantity per Order: 1

GGG reference sample (P507) mounted in quartz tube sample holder. For use with MPMS3 AC Option.

Quantity per Order: 1

This adapter provides the interface between the MPMS3 carbon fiber rod, and the drinking straw, used to mount the sample. For detailed information, refer to the Application Note QDS-1500-018 - Using Straw Sample Holder with DC Scan Mode.

Quantity per Order: 1

Includes Sealed Liquid Sample Holder (QDS-4084-266) and Adapter (QDS-4500-654) for use with MPMS3 Sample Rod.

Quantity per Order: 1

Sample holder made of Teflon for sealing liquid samples in the bucket. Some liquids might require additional use of teflon tape of epoxy glue for better sealing.

Quantity per Order: 1

Adapter for coupling RSO Sealed Sample Holder (QDS-4084-266) to MPMS3 Sample Rod (C135).

Quantity per Order: 1

Bucket only, spare part for RSO or MPMS3 Sealed Sample Holder.

Quantity per Order: 1

Quantity per Order: 1

Quantity per Order: 1

The rod is made of stainess steel and quantum alloy for lower background signal.

Quantity per Order: 1

Quantity per Order: 1

Pd reference sample, not mounted. The sample has 99.99% purity, L=3.81mm, D=2.7mm, defined mass ans magnetic susseptibilty (see Certificate QDS-1041-001 for details).

Quantity per Order: 1

Quarz tube sample holder, like used for Pd reference sample mounting.

Quantity per Order: 1

The rod is made of carbon, require QD-C119 extension.

Quantity per Order: 1

Extention for QD-C118 RSO Rod, also made of carbon.

Quantity per Order: 1

Quantity per Order: 1

Sample holder made of Teflon for sealing liquid samples in the bucket. Some liquids might require additional use of teflon tape of epoxy glue for better sealing.

Quantity per Order: 1

RSO Rod made of stainless steel and quantum alloy, withstands high temperatures and can be used with Oven Option.

Quantity per Order: 1

Mounted in a Straw. Reference sample for AC verification, mass is not defined, can have traces of impurities. See QD-P507 instead.

Quantity per Order: 1

Same shape and size as Pd sample

Quantity per Order: 1

Pd reference sample, not mounted. The sample has 99.99% purity, L=3.81mm, D=2.7mm, defined mass ans magnetic susseptibilty (see Certificate 1041-001 for details).

Quantity per Order: 1

Quantity per Order: 1

Ceramic-based water soluble adhesive commonly used to attach samples to the QD-C145 or QD-P127A Heater Stick. Offers low background signal. Each bottle contains approximately 7 ml.

Quantity per Order: bag of 100

Size #4 clear gelatin capsules, used for pharmaceuticals. Magnetically clean and provide an easy mount to samples. Fits inside the Straws (QDS-AGC2).

Quantity per Order: box of 500

Magnetically clean, the simple drinking straws provide an easy sample mount for the MPMS XL and MPMS3 DC Scan measurements. Not suitable for the VSM measurements.

Quantity per Order: bag of 100

Size #4 clear polycarbonate capsules. Magnetically clean and fit inside the Straws. Have lower bacground and more durable than AGC1 Gelatin Capsules.

Quantity per Order: tube 100g

Standard vacuum grease. Sutable for use at room temperature.

Quantity per Order: tube 25g

Low Temperature Grease. Suitable for use at cryogenic temperatures but melts above room temprature.

Quantity per Order: tube 25g

High Temprature Grease. Sutable for use in 200-400K temperature range.

Quantity per Order: 1

Silver based, two component epoxy (comes in two 28.4 gram containers, has one year shelf live). Suitable for use at cryogenics tempratures.

Quantity per Order: 1

The Kapton tape has good dielectric qualities, low outgassing rate and comparatively high thermal contactivity even lowest temperatures, which makes it an excellent choice for use with cryogenic applications.

Quantity per Order: 1

The Kapton tape has good dielectric qualities, low outgassing rate and comparatively high thermal contactivity even lowest temperatures, which makes it an excellent choice for use with cryogenic applications.